Tuning

Showing 25-48 of 78 item(s)

ARCA Swiss rail for M-LOK

ARCA Swiss rail for M-LOK 2

Weapon accessories

ARCA Swiss rail for M-LOK

The ARCA Swiss rail is a great addition to any rifle that has a chassis with an M-LOK clamping system. It can be used wherever the weapon uses a forend (chassis) with an M-LOK clamping system. A typical example is the weapons used for PRS shooting disciplines.This will give you a big advantage! You can easily move bipods or other accessories efficiently...

View

Trigger resistance spring CZ 557, 550 and 527

Tuning

Trigger resistance spring CZ 557, 550 and 527

Spring used to reduce the resistance of the trigger CZ 557, CZ 550, CZ 527 and increase its accuracy.Using the trigger spring, you can reduce the resistance of the trigger up to 0.5 kg.When the lowest trigger resistance is set, firing may occur when the weapon is unlocked! This fact must be taken into account! For the above reasons, we do not recommend...

View

CZ 457 trigger resistance springs

Tuning

CZ 457 trigger resistance springs

A set of springs used to reduce the resistance of the CZ 457 trigger and increase its accuracy.The set includes two springs, with the trigger spring reducing the factory resistance of the trigger by -50% and the impact spring, which has a 10% higher resistance. Using the trigger spring, you can reduce the trigger resistance to 0.5 kg.A stronger impact...

View

Trigger resistance spring TIKKA T3, T3x and T1x

Tuning

Trigger resistance spring TIKKA T3, T3x and T1x

Spring used to reduce the resistance of the trigger for TIKKA T3, T3x, T1x and increase its accuracy.Using the trigger spring, you can reduce the resistance of the trigger up to 0.5 kg. When the lowest trigger resistance is set, firing may occur when the weapon is unlocked! This fact must be taken into account! For the above reasons, we do not recommend...

View

Trigger resistance springs for CZ 455 / ZKM 452

Tuning

Trigger resistance springs for CZ 455 / ZKM 452

A set of springs used to reduce the resistance of the CZ 455 trigger from the factory 1.3 kg to 0.3 kg, according to your preferences. The strength of the trigger resistance is affected by more factors than just the force of the springs. Therefore, take the achievable resistance as a guide, it can vary by a few percent. The adjusting nuts on the spring...

View

Trigger resistance springs CZ P-10

Tuning

Trigger resistance springs CZ P-10

The set of springs is used to reduce the resistance of the trigger of the CZ P-10 pistol. Our set of springs is fully compatible with variants of pistols S, C, SC, F and contains two versions of the impact spring.One reduces the resistance of the trigger by 0.25 kg, the other by 0.5 kg, so it only depends on you which variant you choose.The springs are...

View

SAKO 75, 85, 595 and 695 trigger resistance spring

Tuning

SAKO 75, 85, 595 and 695 trigger resistance spring

Spring used to reduce the resistance of the trigger SAKO 75, 85 595, 695 and increase its accuracy.Using the trigger spring, you can reduce the resistance of the trigger up to 0.5 kg.When the lowest trigger resistance is set, firing may occur when the weapon is unlocked! This fact must be taken into account! For the above reasons, we do not recommend...

View

Trigger resistance springs for CZ SCORPION EVO

Tuning

Trigger resistance springs for CZ SCORPION EVO

A set of springs used to reduce the resistance of the trigger from the factory 5kg to 2.5kg. The CZ SCORPION EVO 3 weapon is designed from the ground up as a service weapon, and for this reason the resistance of the trigger and its characteristics are designed to maintain shooting safety even in crisis situations and shooting in gloves. During the...

View

Browning X-BOLT trigger resistance spring

Tuning

Browning X-BOLT trigger resistance spring

Spring used to reduce the resistance of the trigger Browning X-BOLT and increase its accuracy.Using the trigger spring, you can reduce the resistance of the trigger up to 0.5 kg.When the lowest trigger resistance is set, firing may occur when the weapon is unlocked! This fact must be taken into account! For the above reasons, we do not recommend setting...

View

Walther LG 300 / LG 400

Walther LG 300 / LG 400 2

Tuning

Walther steel cartridge plug

Spare part for WALTHER steel cartridges.Long-term use of some Walther steel cartridges wears out the thread on the cartridge. This is manifested mainly by the fact that there is a layer of small brass sawdust in the area of the pressure regulator.Over time, the thread on the cartridge becomes so worn that the thread does not withstand the air pressure...

View

Filling PIN for WALTHER air rifles (universal)

Filling PIN for WALTHER air rifles (universal) 2

Tuning

Filling PIN for WALTHER air rifles (universal)

Universal filling PIN (valve) for WALTHER air rifles and pistols. The filling pin is designed for both types of cylinders, so it can be mounted on both 200 and 300 bar pressure bottles (bombs).

View

Enlargement of the Walther LG 300 pressure regulator chamber

Enlargement of the Walther LG 300 pressure regulator chamber 2

Tuning

Enlargement of the Walther LG 300 pressure regulator chamber

Ring for enlarging the chamber of the pressure regulator for the Walther LG 300 air rifle.The chamber of the standard pressure regulator of the PCP air rifle Walther LG 300 is designed for shooting with a power of 7.5J. With our rings, you can easily achieve an enlargement of the chamber and thus the possibility to set the power of the Walther LG 300 air...

View

Reduction for Walther LG 400

Reduction for Walther LG 400 2

Tuning

Reduction for Walther LG 400

By replacing the pressure regulator from the LG 400 with a pressure regulator from the LG 300, you will get much greater setting options and the excellent Walther LG 400 air rifle will thus enter a whole new dimension.In the Czech Republic, the limit for an air rifle is in category D (over-the-counter from the age of 18) to 16J. So why not make the most...

View

Silencer for Walther LG 300/400

Silencer for Walther LG 300/400 2

Tuning

Silencer for Walther LG 300/400

You have a Walther LG 300 or Walther LG 400 air rifle and you don't want to disturb your neighbors with training noise. Then fit a standard front sight that you have on your air rifle with our reduction set. You will get an almost inaudible shot and you can improve your shooting skills at home.The set contains all the necessary components and its assembly...

View

Walther regulator pressure transducer

Walther regulator pressure transducer 2

Tuning

Walther regulator pressure transducer

Do you have a Walther LG 300 or Walther LG 400 air rifle and need to set the correct pressure on the regulator or check if your regulator is working properly?The device we manufacture for precise adjustment and pressure measurement will allow you to do so comfortably and quickly.The pressure transducer is universal for Walther LG 300 and Walther LG 400...

View

Walther LG 300 tension lever pin

Walther LG 300 tension lever pin 2

Tuning

Walther LG 300 tension lever pin

The Walther LG 300 air rifle has a relatively long tension lever, so if you fit it with a riflescope, you will encounter a problem that the original tension lever cannot be pulled. All that remains is to remove and shorten the tension lever. You can then fit it with a duralumin pin made by us. We supply the tensioning pin in silver or black.The set...

View

Mirage band elastic (thermal shield)

Mirage band elastic (thermal shield) 2

Weapon accessories

Mirage band elastic (thermal shield)

The (Lenta) mirage band is designed for all types of rifles and is made from a highly durable and elastic material designed to divert heat from the barrel to prevent negative thermal effects from the mirage. The mirage is a thermal phenomenon that causes optical illusion. The Lenta (mirage band - thermal shield) helps to eliminate this.

View

External WEAVER for mirage band

External WEAVER for mirage band 2

Weapon accessories

External WEAVER for mirage band

External WEAVER handle of lenta (mirage band - heat screen) for situations, when a rifle isn´t equipped with the handle in standard. Our handle is ready for installation on the weaver rail and it is suitable for any regular lenta (mirage band). Handle of lenta is easilly installed on weaver rail (approx. 10 sec.), light and made of quality aerial...

View

Duralumin grips for CZ 75 and their clones

Duralumin grips for CZ 75 and their clones 2

Tuning

Duralumin grips for CZ 75 and their clones

High-quality and very precisely processed duralumin butts for CZ self-loading pistols. The grips are intended for all those who want to equip their weapon with something unconventional, exceptional and at the same time perfectly functional. Mounting the grips is very easy, so you're done in a few minutes. The screws are included in the package.

View

Return spring guide CZ 75 SP-01, Shadow, Tactical Sport

Tuning

Return spring guide CZ 75 SP-01, Shadow, Tactical Sport

Very high quality, refined and polished return spring guide. By using this guide you will achieve better weapon behavior. Made of high quality steel.

View

Mounting of the SHIELD SIGHTS SMS/RMS and RMSc COLLIMATOR...

Tuning

Mounting of the SHIELD SIGHTS SMS/RMS and RMSc COLLIMATOR for CZ 75 SP-01 Shadow, CZ...

The high-quality mount for the SHIELD SIGHTS SMS/RMS/RMSc collimator is very easy to replace with the original standard sights. No modifications to the weapon are required and the original sights can be reinstalled at any time. The mounting of the collimator sight is made of refined steel and will serve you 100% for decades.

View

Mounting of SHIELD SIGHTS SMS/RMS and RMSc COLLIMATOR for...

Tuning

Mounting of SHIELD SIGHTS SMS/RMS and RMSc COLLIMATOR for GLOCK

The high-quality mount for the SHIELD SIGHTS SMS/RMS/RMSc collimator is very easy to replace with the original standard sights. No modifications to the weapon are required and the original sights can be reinstalled at any time. The assembly of the collimator sight is made of refined steel and will serve you 100% for decades.

View

Front sight CZ FO 1mm

Tuning

Front sight CZ FO 1mm

The CZ FO front sight with light-conducting fiber 1mm wide 3.3mm with a height of 5.75mm is suitable for a fixed sight for CZ P-07, CZ P-09, CZ P-10 C. It stands out for its highly precise processing and precise geometry. The viewing surface is roughened against unwanted glare.The front sight is suitable for CZ P-07, CZ P-09, CZ P-10 C pistols, where it...

View

Front sight CZ P-10C FO 1.5mm

Tuning

Front sight CZ P-10C FO 1.5mm

The CZ P-10 C front sight with light guide fiber 1.5 mm wide 3.2 mm and 9 mm high is suitable for the adjustable sight of the CZ P-10 C pistol. It stands out for its highly precise processing and precise geometry. The viewing surface is roughened against unwanted glare.The front sight is suitable for CZ P-10 C pistols, where it is fixed in a longitudinal...

View

1
2
3
4

Product added to wishlist

Product added to compare.