TACTICAL EVO - Hlavní strana

Showing 49-72 of 129 item(s)

SAKO 75, 85, 595 and 695 trigger resistance spring

Tuning

SAKO 75, 85, 595 and 695 trigger resistance spring

Spring used to reduce the resistance of the trigger SAKO 75, 85 595, 695 and increase its accuracy.Using the trigger spring, you can reduce the resistance of the trigger up to 0.5 kg.When the lowest trigger resistance is set, firing may occur when the weapon is unlocked! This fact must be taken into account! For the above reasons, we do not recommend...

View

Bubble level 30mm LIBELA

Bubble level 30mm LIBELA 2

Weapon accessories

Bubble level 30mm

The quality 30mm spirit level has been tested by our competitive shooters. Its construction is designed to withstand the high-powered weapons you may encounter in hunting and sniper rifles. The mounting system is made of anodized aircraft grade aluminum 6065T.It is a quality spirit level for reasonable money!

View

Trigger resistance springs for CZ SCORPION EVO

Tuning

Trigger resistance springs for CZ SCORPION EVO

A set of springs used to reduce the resistance of the trigger from the factory 5kg to 2.5kg. The CZ SCORPION EVO 3 weapon is designed from the ground up as a service weapon, and for this reason the resistance of the trigger and its characteristics are designed to maintain shooting safety even in crisis situations and shooting in gloves. During the...

View

Browning X-BOLT trigger resistance spring

Tuning

Browning X-BOLT trigger resistance spring

Spring used to reduce the resistance of the trigger Browning X-BOLT and increase its accuracy.Using the trigger spring, you can reduce the resistance of the trigger up to 0.5 kg.When the lowest trigger resistance is set, firing may occur when the weapon is unlocked! This fact must be taken into account! For the above reasons, we do not recommend setting...

View

Mounting two-piece 25.4mm (1 ") on 11mm rail - LOW

Mounting two-piece 25.4mm (1 ") on 11mm rail - LOW 2

Weapon accessories

Mounting two-piece 25.4mm (1 ") on 11mm rail - LOW

Two-piece LOW duralumin mounting is designed for riflescopes with a smaller objective, usually up to 40 mm. The attachment is by means of a screw on each part. This mount is suitable for mounting a riflescope or any other device with a 25.4 mm (1 ") tube. The mounting is designed for an 11 mm rail.

View

Walther LG 300 / LG 400

Walther LG 300 / LG 400 2

Tuning

Walther steel cartridge plug

Spare part for WALTHER steel cartridges.Long-term use of some Walther steel cartridges wears out the thread on the cartridge. This is manifested mainly by the fact that there is a layer of small brass sawdust in the area of the pressure regulator.Over time, the thread on the cartridge becomes so worn that the thread does not withstand the air pressure...

View

Two-piece mounting 30mm on 11mm rail - LOW

Two-piece mounting 30mm on 11mm rail - LOW 2

Weapon accessories

Two-piece mounting 30mm on 11mm rail - LOW

Two-piece LOW duralumin mounting is designed for riflescopes with a smaller objective, usually up to 40 mm. The attachment is by means of a screw on each part. This mount is suitable for mounting a riflescope or any other device with a 30mm tube. The mounting is designed for 11mm rail.

View

Filling PIN for WALTHER air rifles (universal)

Filling PIN for WALTHER air rifles (universal) 2

Tuning

Filling PIN for WALTHER air rifles (universal)

Universal filling PIN (valve) for WALTHER air rifles and pistols. The filling pin is designed for both types of cylinders, so it can be mounted on both 200 and 300 bar pressure bottles (bombs).

View

Enlargement of the Walther LG 300 pressure regulator chamber

Enlargement of the Walther LG 300 pressure regulator chamber 2

Tuning

Enlargement of the Walther LG 300 pressure regulator chamber

Ring for enlarging the chamber of the pressure regulator for the Walther LG 300 air rifle.The chamber of the standard pressure regulator of the PCP air rifle Walther LG 300 is designed for shooting with a power of 7.5J. With our rings, you can easily achieve an enlargement of the chamber and thus the possibility to set the power of the Walther LG 300 air...

View

Reduction for Walther LG 400

Reduction for Walther LG 400 2

Tuning

Reduction for Walther LG 400

By replacing the pressure regulator from the LG 400 with a pressure regulator from the LG 300, you will get much greater setting options and the excellent Walther LG 400 air rifle will thus enter a whole new dimension.In the Czech Republic, the limit for an air rifle is in category D (over-the-counter from the age of 18) to 16J. So why not make the most...

View

Silencer for Walther LG 300/400

Silencer for Walther LG 300/400 2

Tuning

Silencer for Walther LG 300/400

You have a Walther LG 300 or Walther LG 400 air rifle and you don't want to disturb your neighbors with training noise. Then fit a standard front sight that you have on your air rifle with our reduction set. You will get an almost inaudible shot and you can improve your shooting skills at home.The set contains all the necessary components and its assembly...

View

Walther regulator pressure transducer

Walther regulator pressure transducer 2

Tuning

Walther regulator pressure transducer

Do you have a Walther LG 300 or Walther LG 400 air rifle and need to set the correct pressure on the regulator or check if your regulator is working properly?The device we manufacture for precise adjustment and pressure measurement will allow you to do so comfortably and quickly.The pressure transducer is universal for Walther LG 300 and Walther LG 400...

View

Walther LG 300 tension lever pin

Walther LG 300 tension lever pin 2

Tuning

Walther LG 300 tension lever pin

The Walther LG 300 air rifle has a relatively long tension lever, so if you fit it with a riflescope, you will encounter a problem that the original tension lever cannot be pulled. All that remains is to remove and shorten the tension lever. You can then fit it with a duralumin pin made by us. We supply the tensioning pin in silver or black.The set...

View

Weapon wiper for all calibers

Weapon wiper for all calibers 2

Weapon accessories

Weapon wiper for all calibers

View

Carbon rods for our LUXURY weapon wiper

Weapon accessories

Carbon rods for our LUXURY weapon wiper

Carbon rods for our LUXURY weapon wiper. We supply carbon rods in diameters of 4, 5, 6, 7, 8 and 10 mm and in lengths of 350, 450, 550, 650, 750, 850, 950 and 1050 mm. So all you need to clean your weapons is a handle, and you put carbon rods in it as you see fit. Replacing one rod with another does not take more than 1 second!The thread at the end of the...

View

Mirage band elastic (thermal shield)

Mirage band elastic (thermal shield) 2

Weapon accessories

Mirage band elastic (thermal shield)

The (Lenta) mirage band is designed for all types of rifles and is made from a highly durable and elastic material designed to divert heat from the barrel to prevent negative thermal effects from the mirage. The mirage is a thermal phenomenon that causes optical illusion. The Lenta (mirage band - thermal shield) helps to eliminate this.

View

External WEAVER for mirage band

External WEAVER for mirage band 2

Weapon accessories

External WEAVER for mirage band

External WEAVER handle of lenta (mirage band - heat screen) for situations, when a rifle isn´t equipped with the handle in standard. Our handle is ready for installation on the weaver rail and it is suitable for any regular lenta (mirage band). Handle of lenta is easilly installed on weaver rail (approx. 10 sec.), light and made of quality aerial...

View

Duralumin grips for CZ 75 and their clones

Duralumin grips for CZ 75 and their clones 2

Tuning

Duralumin grips for CZ 75 and their clones

High-quality and very precisely processed duralumin butts for CZ self-loading pistols. The grips are intended for all those who want to equip their weapon with something unconventional, exceptional and at the same time perfectly functional. Mounting the grips is very easy, so you're done in a few minutes. The screws are included in the package.

View

Return spring guide CZ 75 SP-01, Shadow, Tactical Sport

Tuning

Return spring guide CZ 75 SP-01, Shadow, Tactical Sport

Very high quality, refined and polished return spring guide. By using this guide you will achieve better weapon behavior. Made of high quality steel.

View

Mounting of the SHIELD SIGHTS SMS/RMS and RMSc COLLIMATOR...

Tuning

Mounting of the SHIELD SIGHTS SMS/RMS and RMSc COLLIMATOR for CZ 75 SP-01 Shadow, CZ...

The high-quality mount for the SHIELD SIGHTS SMS/RMS/RMSc collimator is very easy to replace with the original standard sights. No modifications to the weapon are required and the original sights can be reinstalled at any time. The mounting of the collimator sight is made of refined steel and will serve you 100% for decades.

View

Mounting of SHIELD SIGHTS SMS/RMS and RMSc COLLIMATOR for...

Tuning

Mounting of SHIELD SIGHTS SMS/RMS and RMSc COLLIMATOR for GLOCK

The high-quality mount for the SHIELD SIGHTS SMS/RMS/RMSc collimator is very easy to replace with the original standard sights. No modifications to the weapon are required and the original sights can be reinstalled at any time. The assembly of the collimator sight is made of refined steel and will serve you 100% for decades.

View

Front sight CZ FO 1mm

Tuning

Front sight CZ FO 1mm

The CZ FO front sight with light-conducting fiber 1mm wide 3.3mm with a height of 5.75mm is suitable for a fixed sight for CZ P-07, CZ P-09, CZ P-10 C. It stands out for its highly precise processing and precise geometry. The viewing surface is roughened against unwanted glare.The front sight is suitable for CZ P-07, CZ P-09, CZ P-10 C pistols, where it...

View

Front sight CZ P-10C FO 1.5mm

Tuning

Front sight CZ P-10C FO 1.5mm

The CZ P-10 C front sight with light guide fiber 1.5 mm wide 3.2 mm and 9 mm high is suitable for the adjustable sight of the CZ P-10 C pistol. It stands out for its highly precise processing and precise geometry. The viewing surface is roughened against unwanted glare.The front sight is suitable for CZ P-10 C pistols, where it is fixed in a longitudinal...

View

Front sight CZ P-10C FO 1mm

Tuning

Front sight CZ P-10C FO 1mm

Front sight CZ P-10 C with optical fiber 1 mm wide 3.2 mm with a height of 9 mm is suitable for the adjustable sight of the CZ P-10 C pistol. It stands out for its highly precise processing and precise geometry. The viewing surface is roughened against unwanted glare.The front sight is suitable for CZ P-10 C pistols, where it is fixed in a longitudinal...

View

1
2
3
4
…
6

Product added to wishlist

Product added to compare.